Installing A Bath tub
Schedule Appointment NowHave you been looking for related information about How to Install a Bathtub?
Installing a bath tub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough task. If the old tub is conveniently available, the job can relocate rapidly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have certified on your own for the work as well as fit attempting it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you may require a professional plumber to make tube links.
This write-up will aid you install a brand-new bath tub in your restroom if you have actually currently purchased a brand-new bathtub as well as do not need to alter the plan of your previous water pipes.
Your tools as well as product list need to comprise the following:
Planning for the Setup
First of all, the sustaining structure supplied with the bath should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be rather problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using both wooden boards under its feet, place the bath tub in the needed placement. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the tub till the spirit level reads level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section on How to Install a Bathtub Yourself. Thanks a ton for taking the time to read our posting. Do you know about someone else who is enthusiastic about the topic? Why not share it. Thanks for going through it.
Schedule Now!